VW Polo 9N 1.9 TDI or SDI - Power Steering Observations
The VW Polo 9N 1.9 TDI or SDI variant has a power steering pump that is located in a strange place.
To top up the fluid you will need to remove the battery (13mm socket set with extender) and also the battery tray (13mm socket with extender and perhaps knuckle).
The a battery tray is also partially attached to the air filter housing, so you will need to wrestle around that too. This video shows the location:
The pump is a 12v electric pump, and is accessed from underneath the car it looks like this:
In the video above you can only see the green cap poking up. The rest is tucked away and is accessed behind the bumper.
VW Polo 9N 1.9 TDI or SDI - Stiff / Lumpy Steering
If you have lumpy / stiff / intermittent power steering then it is likely that you have low power steering fluid levels. You should top up your power steering fluid level. BUT. . .before you do have a look under the car, is there oil dribbling out near the power steering rack. You may have a leak.
If you do have a leak you could either take it to the garage, and pay them £400 for a new rack, or you can use some power steering sealant. I have used the "Lucas" branded stuff and it is good. It gets consistently good reviews by everybody that uses it.
VW Polo 9N 1.9 TDI or SDI - Without Power Steering
I am a fit, well fed, 6ft tall man, who liked wrestling alligators (made up that last part) the steering in a vw polo is reeeeally heavy without power steering. Much much heavier than an old car designed without power steering.Forums are full of storey of people installing manual racks and then going back to power steering.
My little blue polo TDI has been a great little car and is already at 165k, and going strong. If that is I can demist the windscreen! There are two problems I have
The temperature control knob does not work very well, getting stuck on either hot or cold.
The fan speed only works on setting 3 and 4.
Problem 2 is dealt with with a replacement part. But please see work around 2 for how I reliably fixed Problem 1. To fix problem 1 properly = ££££ or $$$$
VW Polo Heater Problems - Heater Fan Speed Fix
On a mark 9 polo this is possibly fixable by the amateur mechanic with adequate patience. There is a great video on you tube posted by Gary Freeburn. This is embedded below:
It basically involves removing the glove box, and some other bit in that area, and then there is a component resembling a circuit board that needs to be replaced. You will need a torx (star shape) screwdriver to do this. From the comments left on the you tube video it looks reasonably easy.
VW Polo Heater Problems - Heater Temperature Control
This problem is a lot more complicated, and if you want to get it fixed properly you are looking at around £500. The mix of hot and cold air flow is controlled by a valve or flap, with a little motor which can be accessed by removing the glove box, and the shelf trim below the glove box. This is also the case in the Skoda Fabia I believe.
There are many good forum posts on how you might repair this:
As you can see its a flipping nightmare to fix, and as my car is probably only worth £2000, I can't be doing with it. However, with a little patience there is a work (wait) around.
VW Polo Heater Problems - Heater Temperature Control - Work Around
Set the temperature control knob some where between 18 and 22 degrees (10 o'clock to 12 o'clock) and then leave it alone. If you heater is stuck on cold, ie.e blowing cold air all of time, even when switched to hot you may have to wait a while for the flaps to adjust, this could be a few days of normal driving, it may help to drive over some bumps, some people have mentioned switching the fans on and off, and pressing the recycle button, but I find waiting is the only thing that works for sure.
Bear in mind having a heater that is stuck on hot, is far better than having it stuck on cold. So once it is blowing hot leave it alone. And . . . open a window if you get hot.
VW Polo Heater Problems - Heater Temperature Control - Work Around 2
As mentioned in the intro the problem is either e burnt out motor or, damaged wiring to the motor that controls the hot and cold air mix flap. The mix is controlled indirectly via a thermostatic controller, lord alone knows where that is. . . Bypass all of this and go old school for a quick and cheap fix, that works well. Click on any of below pictures to enlarge.
Annotated Diagram - Better Picture of Same View 2 Below
Same View As above - Better below
Note brightly lit cog type thing, this is falp for controlling temperature
This is the motor that you can get rid of.
There might be a pink bit on connector, to help identify motor location
View from below teeth of flap arm / arm visable.
Use a cold start / choke pull bale to operate flap.
Fix cable outer in place firmly, but do not squash.
Carefully drill hole in flap arm / cam and attach end of choke wire or cable.
The choke cable which I use was solid wire type which was pretty handy, as I could bend the end around to fasten in to the flap arm / cam and also it "pushes" as well as pulls wells. The flap arm / lever / cam will need to be pushed up wards to get hot air, and pulled down to get cold air. A cable (rather then wire) may buckle when in used in this way.
Rather than dismantle the whole dashboard to unscrew the top of the clip that holds the motor in place, you can just break the clip open at the bottom and pull the crappy motor out.
If you wanted to keep this really simple, why not just attached a piece of coat hanger to the arm and have it poking down in to foot well, to switch on a off when required.
Another option might be to screw the flap arm in place half open half closed, for luke warm air all the time. . . maybe.
A few months back my ECU logged a P0299 fault code on our audi 1.9 TDI PD (BRB). On opening up the engine I notice a split pipe that returns exhaust gas from the EGR cooler, which its self was loose.
Not being a mechanic, a tightned up the EGR cooler mounting and welded the pipe back together.
What I should have done was considered why the EGR cooler had come loose.
To my untrained ear the BRB engine had always sounded bit "butch" and noisier than our other 1.9 PD powered VW. The noise it turned out was actually a mis-fire of one cylinder.
The problem was that the previous owber had driven the car 120,000 miles for some or all of which he had used a low grade oil. This had resulted in the can shaft lodes wearing down to the point wehere, the exhust valve from one of cylinders no longer opened, which meant the only route was back out through the inlet valve.
This results in a lack of power, and a severse accelalration lag, ending in a jerky accelaration.
On inspection the lobes on the cam shaft were noticlbly worn, and you could see the wear with the naked eye.
It is likley that this forcing of exhaust gas back through the inlet valve caused the over opressurusation of teh EGR system, which may have caused shrink swell and subsequent lossening, and eventually the split EGR return pipe.
P0299 Fault Code on Audi A4 1.9 TDI BRB Engine - Intro
Our Audi A4 1.9 TDI suffered an obvious loss of boost and the engine light showing. I plugged in the OBD scanner and it flagged up a P0299 fault code described as "turbo booster under boost".
So armed with this code I went on various forums here and there to see what I could find out. However, I should have opened up the bonnet first, as the problem would have been immediatly obvious. THIS MAY HAVE ULTIMATLY BEEN DUE TO A WORN CAM SHAFT.
P0299 Fault Code on Audi A4 1.9 TDI BRB Engine - Forums and Other Sources
1 - Apparently a common cuase for this code is a faulty pressure convertor valve.
"I
would look at the Pressure Converter Valve (N75) located above the brake
booster. It controls vacuum to the turbo. The part number is 1K0906627A. Here
is a link to a picture of it http://www.idparts.com/catalog/produ...oducts_id=1251 .
Hope that helps you out, mine was doing the same thing - no boost, no cruise
control, and same code."
2 - The BRB engine has a variable geometry turbo, with bits that move inside, these moving bits are pulled / pushed by an actuator. "Check your boost actuator with a vacuum pump from the
autopart store. Autozone sells one that will be perfect for what you are
testing. I guess I
should do the test just to rule it out but I don't see how that could possibly
be the problem given the fact that when it goes into "wimp mode"
(that’s what I call it cuz it's not "Limp Mode") all I have to do is
unplug the MAF sensor and Whaaalaaaa, got all my power back. The boost actuator
is a mechanical device that I don’t believe can be fixed by unplugging the MAF.
Please correct me if I’m wrong."
3 - If the Actuator is the problem, then you will need to figure out which brand you have, actuators can only be sourced from specialist companies and not from your average parts place, they may require that you make a custom brcket for them to fit!
Borg/warner
turbo rod extends with applied vacume.
Garret
Turbo rod retracts with applied vacume.
Actuator
type blck box = electronic – silver and round = mechanical.
P0299 Fault Code on Audi A4 1.9 TDI BRB Engine - Actual Problem in my Case
There is an exhauist gas pipe that comes out of the EGR cooler, and upon opening the bonnet it was immediatly obvious that this had broken (stress fracture) and there was soot every where. The host gases had also melted a hole in the plastic engine cover.
It is unclear as to why this pipe has failed and one reason is :
"Good call Tom_B...EGR cooler was loose. The engine is doing
some serious vibrating and some of the bolts had been damaged from the
vibration so they replaced the mid and the rear bolts. I hadn't opened the hood
with the engine running in a while and I was surprised by how much vibration
was going on in there. I guess I got accustomed to it."
SO check that.
I found a loose bolt on the EGR cooler essembly, see below, so I teightened that and had the EGR pipe welded up by a local fabricator. I will post back in a few months and tell how things are going. There are other bolts that should be checked for tightness, but they are hard to get to.